S5M-360 rubber timing belt
This S5M-360 closed-loop timing belt is listed with a 25 mm width. Match the complete marking and S5M tooth profile to your pulley, and include the required quantity and equipment details when requesting a replacement.
| Item | Product details |
|---|---|
| Designation | S5M-360 |
| Belt form | Closed-loop rubber timing belt |
| Profile pitch | 5 mm (S5M) |
| Width | 25 mm |
| Replacement match | Full marking, length and pulley profile |
Send your drawing, required quantity and operating conditions to request a quote.
Match the S5M profile
Match the complete S5M profile rather than pitch alone: different profile families can share a 5 mm pitch while using different tooth geometry. Check the belt marking and pulley drawing together, and specify the required rubber, tensile reinforcement and tooth-facing material for your working conditions.
| Detail | Information to provide |
|---|---|
| Belt identification | Complete printed marking, equipment model and part number |
| Dimensions | Width, finished length or tooth count, and pulley profile |
| Construction | Rubber material, tensile-cord and tooth-fabric requirements; joint or endless arrangement |
| Working conditions | Speed, load, temperature, bending arrangement and contact with oils or cleaning agents |
Rubber timing-belt profile reference
The following dimensions cover several profile families in the range. Match the complete profile designation to your pulley; a shared pitch alone does not establish interchangeability. The STPD/STS S5M row gives a 5 mm pitch, 1.91 mm tooth height and 3.4 mm belt thickness as range references. Use the complete S5M-360 designation and finished-belt drawing for the replacement order.
| Profile | Pitch (mm) | Tooth height (mm) | Belt thickness (mm) |
|---|---|---|---|
| MXL | 2.032 | 0.51 | 1.14 |
| XXL | 3.175 | 0.76 | 1.52 |
| XL | 5.080 | 1.27 | 2.30 |
| L | 9.525 | 1.91 | 3.60 |
| H | 12.70 | 2.29 | 4.30 |
| XH | 22.225 | 6.35 | 11.20 |
| XXH | 31.750 | 9.53 | 15.70 |
| HTD 2M | 2 | 0.75 | 1.36 |
| HTD 3M | 3 | 1.17 | 2.4 |
| HTD 5M | 5 | 2.06 | 3.8 |
| HTD 8M | 8 | 3.36 | 6.00 |
| HTD 14M | 14 | 6.02 | 10.00 |
| HTD 20M | 20 | 8.4 | 13.20 |
| STPD/STS S2M | 2 | 0.76 | 1.36 |
| STPD/STS S3M | 3 | 1.14 | 2.2 |
| STPD/STS S4.5M | 4.5 | 1.71 | 2.81 |
| STPD/STS S5M | 5 | 1.91 | 3.4 |
| STPD/STS S8M | 8 | 3.05 | 5.3 |
| STPD/STS S14M | 14 | 5.3 | 10.2 |
| RPP 8M | 8 | 3.2 | 5.5 |
| RPP 14M | 14 | 6.00 | 10 |
Custom processing
If the replacement requires a covering, holes, guides or other processing, show their dimensions and locations on the drawing. Include close-up photographs of the tooth side, back surface and any processed features so we can discuss the required arrangement.
